donimo's first "just for fun" rig

[donimo]

So, I finished getting it together enough to run, couple snags but it booted up first try, so sweeeet.


Here are some pics, excuse the crappyness, too lazy to get the camera that works:









So, this case ain't perfect, had to solder in an extension for the power/reset leads, great idea Antec, make cables that don't reach the bottom of a motherboard, only half of all mobo's put them there .

I only ended up cutting 2 holes, one by the power supple, and one 10cm in from the ps2 ports for the 4 pin CPU, it came with the 2 by the drive bays.

I also put in carbon filters in each drive blank, and a foam one on the 120mm side fan hole, still want to swap the vented pci brackets for solids, then 90% of the incoming air will be filtered. I added a yate loon 120 to the back of a drive bay and moved it to the top blowing on the RAM and CPU, for 99 cents I thought why not (still have 4).

The thermalrite hr-05 only fit one way with the freezer 7, and that had it about 2mm from the backside of the vid card, so I added a $2 scythe 40mm to the stock hs, so far so good.

Even with the filter restriction I am getting AMAZING temps for an air-cooled case.

CPU- 39*C with atitool and 4 cpuburns running (orthos later)
GPU- 36*c atitool
hdd 28*
ambient- 30
NB- 33

So, I think its a go for baseline benching then o/c trials, Im happy with how it turned out so far, not bad for $620 after taxes.

[Prof. Dr. Silver]

As Howie says: OPEN THE CASE! lol...have fun OCing

[jdrom17]

Nice cheap setup

However, it looks like your sidepanel doesn't have any plastic/plexiglass behind the metal mesh stuff?

Take off the side-panel and snap a pic as well.

[donimo]

ok, pics away:







This one just shows the mini kaze fan, only 14dB






CPU at idle is 16*C, it is cold in the basement, but still! This is with eztune, the gigabyte s/w, and it is bang on upstairs...

[donimo]

Originally Posted by jdrom17

Nice cheap setup

However, it looks like your sidepanel doesn't have any plastic/plexiglass behind the metal mesh stuff?

Take off the side-panel and snap a pic as well.

It does, thats what holding in the "filter".

[Theblackmages]

Not bad at all.
I'm sure you could still work that cable management a bit.
My dad just picked up a Dremel today, So I'm thinking about cuting a side panel for my CM690.I'll do that, cut a couple of places for some better cable management, Paint the interior of the case black and perhaps cut some restrictive metal for the fans. so yeah I'll post pics of it when my project will be done :)

[donimo]

Sweet, I like the 690 a lot.

I will be reorganizing for sure, just a "tired of soldering on my knees" quickie job.

[Prof. Dr. Silver]

I'm starting to dislike the CM690 just for the fact that A LOT OF PSU's have SHORT cables! Dang, today I put another PSU in my case....and again too short! I do not like BOTTOM mounted PSU cases!!!

Ps. Sorry to steel your thread...I like your case though!

[enaberif]

Originally Posted by Prof. Dr. Silver

I'm starting to dislike the CM690 just for the fact that A LOT OF PSU's have SHORT cables! Dang, today I put another PSU in my case....and again too short! I do not like BOTTOM mounted PSU cases!!!

Ps. Sorry to steel your thread...I like your case though!

Can't hate the 690 for that; hate bottom mounted psus.

My PC P&P 750 8pin JUST reaches.

[donimo]

My crappy power supply turned out perfectly for cable length, plus fully sleeved cables to boot, too bad it wasnt a better unit, but we'll see how she goes...

For the record I bumped it up to 266fsb, 2.67ghz cpu, 1066 ram, stock voltages on everything, ran like a charm!