Go Back   Hardware Canucks > PC BUILDERS & TWEAKERS CORNER > Troubleshooting

    
Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old December 12, 2008, 02:30 PM
Rookie
 
Join Date: Sep 2008
Posts: 25
Default Vista 64 BSOD: IRQL_NOT_LESS_OR_EQUAL

Well oddly enough the harddrive with XP that I use has crashed and Xp was vary flakey and would crash randomly and I think even corrupted some files while i was using it, so i went onto my second hard drive which has Vista x64 SP1 and even that is BSODing, the other hard drive is disconected so there should be no interferance and i downloaded the newest software as there was nothing installed on it at all. So here is the info from my memory dump in Vista:

Code:
IRQL_NOT_LESS_OR_EQUAL (a)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high.  This is usually
caused by drivers using improper addresses.
If a kernel debugger is available get the stack backtrace.
Arguments:
Arg1: 0000000000000040, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, bitfield :
    bit 0 : value 0 = read operation, 1 = write operation
    bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status)
Arg4: fffff80001d436f2, address which referenced memory

Debugging Details:
------------------

Page bc6d6 not present in the dump file. Type ".hh dbgerr004" for details
PEB is paged out (Peb.Ldr = 000007ff`fffdf018).  Type ".hh dbgerr001" for details
PEB is paged out (Peb.Ldr = 000007ff`fffdf018).  Type ".hh dbgerr001" for details

READ_ADDRESS:  0000000000000040 

CURRENT_IRQL:  2

FAULTING_IP: 
nt!MiIdentifyPfn+6f2
fffff800`01d436f2 498b5b40        mov     rbx,qword ptr [r11+40h]

DEFAULT_BUCKET_ID:  VISTA_DRIVER_FAULT

BUGCHECK_STR:  0xA

PROCESS_NAME:  svchost.exe

TRAP_FRAME:  fffffa600b0e2630 -- (.trap 0xfffffa600b0e2630)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=0200000000000000 rbx=0000000000000200 rcx=0000000000000002
rdx=00000000001d3918 rsi=0000000000000000 rdi=fffff80001d9177f
rip=fffff80001d436f2 rsp=fffffa600b0e27c0 rbp=fffffa600b0e2800
 r8=0200000000000000  r9=0000000000000442 r10=fffffa8004263f90
r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei ng nz na po nc
nt!MiIdentifyPfn+0x6f2:
fffff800`01d436f2 498b5b40        mov     rbx,qword ptr [r11+40h] ds:18c0:0040=????????????????
Resetting default scope

LAST_CONTROL_TRANSFER:  from fffff80001cb30ee to fffff80001cb3350

STACK_TEXT:  
fffffa60`0b0e24e8 fffff800`01cb30ee : 00000000`0000000a 00000000`00000040 00000000`00000002 00000000`00000000 : nt!KeBugCheckEx
fffffa60`0b0e24f0 fffff800`01cb1fcb : 00000000`00000000 fffffa80`009569d0 fffffa80`04eb6000 00000580`00000000 : nt!KiBugCheckDispatch+0x6e
fffffa60`0b0e2630 fffff800`01d436f2 : fffffa80`05471000 00000000`000018c0 fffff800`01df1160 00000000`00000001 : nt!KiPageFault+0x20b
fffffa60`0b0e27c0 fffff800`01d5dffe : 00000000`0003a723 fffffa80`054722d0 fffffa80`073c4060 00000000`00000000 : nt!MiIdentifyPfn+0x6f2
fffffa60`0b0e2860 fffff800`0204cd75 : fffffa80`05471000 fffffa60`0b0e2ca0 fffffa60`0b0e2928 00000000`00000000 : nt!MmQueryPfnList+0x13e
fffffa60`0b0e28a0 fffff800`01f942dc : fffffa80`000000a8 00000000`00000000 fffffa80`05471000 00000000`05aa6f01 : nt!PfpPfnPrioRequest+0x115
fffffa60`0b0e28f0 fffff800`01f2954a : 00000000`00000000 00000000`05aa6ff0 00000000`0427ee60 fffff800`0204cd01 : nt! ?? ::NNGAKEGL::`string'+0x46bea
fffffa60`0b0e2960 fffff800`01cb2df3 : fffffa80`073c4060 00000000`05aa6ff0 00000000`08078b20 00000000`00000000 : nt!NtQuerySystemInformation+0xd0a
fffffa60`0b0e2c20 00000000`77185dda : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13
00000000`0427edb8 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x77185dda


STACK_COMMAND:  kb

FOLLOWUP_IP: 
nt!MiIdentifyPfn+6f2
fffff800`01d436f2 498b5b40        mov     rbx,qword ptr [r11+40h]

SYMBOL_STACK_INDEX:  3

SYMBOL_NAME:  nt!MiIdentifyPfn+6f2

FOLLOWUP_NAME:  MachineOwner

MODULE_NAME: nt

DEBUG_FLR_IMAGE_TIMESTAMP:  48d1ba35

IMAGE_NAME:  memory_corruption

FAILURE_BUCKET_ID:  X64_0xA_nt!MiIdentifyPfn+6f2

BUCKET_ID:  X64_0xA_nt!MiIdentifyPfn+6f2

Followup: MachineOwner
I read a bit online and its seems that it could be either RAM or driver problems, but I used memtest and it passed 6 times (around 6 hours), drivers also seem unlikely as they are all new and not that many. Another thing to mention is that it crashes constantly, meaning everytime I leave it overnight or while i'm away at school.

My specs anyway are:
Vista x64 SP1
7800 GT OC
4Gb 4( Crucial Ballistix 1GB matched)
Intel Q600
Asus P5K Premium Wifi Ap

Last edited by magixx; December 12, 2008 at 06:26 PM.
Reply With Quote
  #2 (permalink)  
Old December 12, 2008, 02:39 PM
enaberif's Avatar
Hall Of Fame
 
Join Date: Dec 2006
Location: Calgahree, AB
Posts: 10,473
Default

Quote:
Originally Posted by magixx View Post
Well oddly enough the harddrive with XP that I use has crashed and Xp was vary flakey and would crash randomly and I think even corrupted some files while i was using it, so i went onto my second hard drive which has Vista x64 SP1 and even that is BSODing, the other hard drive is disconected so there should be no interferance and i downloaded the newest software as there was nothing installed on it at all. So here is the info from my memory dump in Vista:

I read a bit online and its seems that it could be either RAM or driver problems, but I used memtest and it passed 6 times (around 6 hours), drivers also seem unlikely as they are all new and not that many. Another thing to mention is that it crashes constantly, meaning everytime I leave it overnight or while i'm away at school.

My specs anyway are:
Vista x64 SP1
7800 GT OC
4Gb 4( Crucial Ballistix 1GB matched)
Intel Q600
What memtest are you using? Is it memtest86+ from Memtest86+ - Advanced Memory Diagnostic Tool and the latest?

You didn't specify what motherboard you used... some Crucial Ballistix don't work with a lot of P35 boards.

Did you run a SmallFFT test with P95?

Did you go into your bios and setup your timings, speeds, and voltages for the memory?
Reply With Quote
  #3 (permalink)  
Old December 12, 2008, 03:09 PM
"Quote This..."
F@H
 
Join Date: Nov 2007
Location: Hell
Posts: 3,828
Default

that error message is pointing to your ide controllers. Have you tried different drivers for them?

What mobo?
Reply With Quote
  #4 (permalink)  
Old December 12, 2008, 03:10 PM
enaberif's Avatar
Hall Of Fame
 
Join Date: Dec 2006
Location: Calgahree, AB
Posts: 10,473
Default

Quote:
Originally Posted by Squeetard View Post
that error message is pointing to your ide controllers. Have you tried different drivers for them?

What mobo?
That error message can also be due to unstable memory.
Reply With Quote
  #5 (permalink)  
Old December 12, 2008, 03:15 PM
Chilly's Avatar
Hall Of Fame
F@H
 
Join Date: Sep 2007
Location: Ontario
Posts: 2,593
Default

I agree with enaberif, the Crusial Ballistix, certain revisions, have issues with some P35 boards. What I would try is bumping up the northbridge voltage a tad(this is what I had to do to get my Ballistix in a 4x1GB on an ASUS P35 P5K configuration stable in my "Spare Parts PC"), then run Memtest86+ overnight for at least 12 hours and see if any errors appear.

What motherboard are you running, simply giving us the chipset isn't enough to help you fully. Personally I'm leaning heavily toward it being a memory, BIOS or motherboard issue.
Reply With Quote
  #6 (permalink)  
Old December 12, 2008, 05:47 PM
Rookie
 
Join Date: Sep 2008
Posts: 25
Default

Sorry I forgot to mention the motherboard. The mobo itself is a P5K Premium Wifi-Ap, I was using memtest86+2.01, but will test the newest (2.10) later tonight. Also all the parts are running at stock speed and I have not changed anything. All my drives are Sata as last time i tried any ide components they did not work. I temporarely took out 2gb of memory and it has not crashed yet but then again it did not crash previously with 4gb while attended.

I am running a blend test now with Prime95. I also notice when lookin at the ram that one pair was 2.0v while the other was 2.2V if this helps.

Last edited by magixx; December 12, 2008 at 06:25 PM.
Reply With Quote
  #7 (permalink)  
Old December 13, 2008, 01:31 AM
enaberif's Avatar
Hall Of Fame
 
Join Date: Dec 2006
Location: Calgahree, AB
Posts: 10,473
Default

Quote:
Originally Posted by magixx View Post
Sorry I forgot to mention the motherboard. The mobo itself is a P5K Premium Wifi-Ap, I was using memtest86+2.01, but will test the newest (2.10) later tonight. Also all the parts are running at stock speed and I have not changed anything. All my drives are Sata as last time i tried any ide components they did not work. I temporarely took out 2gb of memory and it has not crashed yet but then again it did not crash previously with 4gb while attended.

I am running a blend test now with Prime95. I also notice when lookin at the ram that one pair was 2.0v while the other was 2.2V if this helps.
You need to check if your memory is single or double sided.

Single sided did NOT work well with P35 boards at all and would cause all sorts of problems.
Reply With Quote
  #8 (permalink)  
Old December 13, 2008, 08:41 AM
"Quote This..."
F@H
 
Join Date: Nov 2007
Location: Hell
Posts: 3,828
Default

Quote:
Originally Posted by magixx View Post
All my drives are Sata as last time i tried any ide components they did not work.
Even your dvd-rom's? Have you disabled the ide controller in the bios then? The fact you could not get ide devices to work should tell you something here.
Reply With Quote
  #9 (permalink)  
Old December 13, 2008, 08:42 AM
"Quote This..."
F@H
 
Join Date: Nov 2007
Location: Hell
Posts: 3,828
Default

Also, i have the same board, had issues with the jmicron sata controller. Disable that and don't use any of the black sata ports.
Reply With Quote
  #10 (permalink)  
Old December 13, 2008, 11:41 AM
Rookie
 
Join Date: Sep 2008
Posts: 25
Default

Ok well I used memtest+ 2.10 for 12 hours with 15 passes and it had 0 errors. Yes even the DVD drive is SATA. I will try to disable IDE controller and then leave the computer on normally and see if I still get a BSOD. If It does BSOD do I might disable the jmicron sata controller depending if I have enough sata port on my PC for the other stuff.

EDIT: Well i had the pleasure of it BSODing again this time with a different error, I was watching a video at the time this happened. Do note that the other hard drive was connected and I had not disabled anything yet. Here is the info:
Code:
SYSTEM_SERVICE_EXCEPTION (3b)
An exception happened while executing a system service routine.
Arguments:
Arg1: 00000000c0000005, Exception code that caused the bugcheck
Arg2: fffff80001cfa6f2, Address of the exception record for the exception that caused the bugcheck
Arg3: fffffa600a5edf60, Address of the context record for the exception that caused the bugcheck
Arg4: 0000000000000000, zero.

Debugging Details:
------------------


EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

FAULTING_IP: 
nt!MiIdentifyPfn+6f2
fffff800`01cfa6f2 498b5b40        mov     rbx,qword ptr [r11+40h]

CONTEXT:  fffffa600a5edf60 -- (.cxr 0xfffffa600a5edf60)
rax=0200000000000000 rbx=0000058000000000 rcx=0000000000000002
rdx=00000000001823b8 rsi=fffffa80047052b0 rdi=02000000000a5c83
rip=fffff80001cfa6f2 rsp=fffffa600a5ee7c0 rbp=fffffa600a5ee800
 r8=0200000000000000  r9=0000000000000542 r10=fffffa8007929080
r11=2064615600010008 r12=0000000000000000 r13=fffffffffffff000
r14=000fffffffffffff r15=0000000000000000
iopl=0         nv up ei ng nz na pe nc
cs=0010  ss=0018  ds=002b  es=002b  fs=0053  gs=002b             efl=00010282
nt!MiIdentifyPfn+0x6f2:
fffff800`01cfa6f2 498b5b40        mov     rbx,qword ptr [r11+40h] ds:002b:20646156`00010048=????????????????
Resetting default scope

CUSTOMER_CRASH_COUNT:  1

DEFAULT_BUCKET_ID:  VISTA_DRIVER_FAULT

BUGCHECK_STR:  0x3B

PROCESS_NAME:  svchost.exe

CURRENT_IRQL:  2

LAST_CONTROL_TRANSFER:  from fffff80001d14ffe to fffff80001cfa6f2

STACK_TEXT:  
fffffa60`0a5ee7c0 fffff800`01d14ffe : 00000000`00030477 fffffa80`047052b0 fffffa80`0751cbb0 00000000`00000000 : nt!MiIdentifyPfn+0x6f2
fffffa60`0a5ee860 fffff800`02003d75 : fffffa80`04705000 fffffa60`0a5eeca0 fffffa60`0a5ee928 00000000`00000000 : nt!MmQueryPfnList+0x13e
fffffa60`0a5ee8a0 fffff800`01f4b2dc : fffffa80`000000a8 00000000`00000000 fffffa80`04705000 00000000`05c04f01 : nt!PfpPfnPrioRequest+0x115
fffffa60`0a5ee8f0 fffff800`01ee054a : 00000000`00000000 00000000`05c04ff0 00000000`02b1eb20 fffff800`02003d01 : nt! ?? ::NNGAKEGL::`string'+0x46bea
fffffa60`0a5ee960 fffff800`01c69df3 : fffffa80`0751cbb0 00000000`05c04ff0 00000000`05770dc0 00000000`00000000 : nt!NtQuerySystemInformation+0xd0a
fffffa60`0a5eec20 00000000`77d25dda : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiSystemServiceCopyEnd+0x13
00000000`02b1ea78 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : 0x77d25dda


FOLLOWUP_IP: 
nt!MiIdentifyPfn+6f2
fffff800`01cfa6f2 498b5b40        mov     rbx,qword ptr [r11+40h]

SYMBOL_STACK_INDEX:  0

SYMBOL_NAME:  nt!MiIdentifyPfn+6f2

FOLLOWUP_NAME:  MachineOwner

MODULE_NAME: nt

DEBUG_FLR_IMAGE_TIMESTAMP:  48d1ba35

STACK_COMMAND:  .cxr 0xfffffa600a5edf60 ; kb

IMAGE_NAME:  memory_corruption

FAILURE_BUCKET_ID:  X64_0x3B_nt!MiIdentifyPfn+6f2

BUCKET_ID:  X64_0x3B_nt!MiIdentifyPfn+6f2

Followup: MachineOwner

Last edited by magixx; December 13, 2008 at 04:27 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
Vista 64 BSOD encorp Troubleshooting 11 December 6, 2008 09:48 PM
BSOD error miggs78 Troubleshooting 9 August 20, 2008 03:22 PM
nv4disp_dll BSOD druwitt Troubleshooting 2 August 11, 2008 04:21 PM
BSOD with 4gbs of Ram vintank RAM 14 February 2, 2008 12:20 AM
BSOD from iTunes? :| curtispan Troubleshooting 3 January 5, 2008 03:23 AM