Hardware Canucks

Hardware Canucks (http://www.hardwarecanucks.com/forum/)
-   Case Mods, Worklog & Gallery (http://www.hardwarecanucks.com/forum/case-mods-worklog-gallery/)
-   -   WIP Rampage (http://www.hardwarecanucks.com/forum/case-mods-worklog-gallery/60310-rampage.html)

Mark March 21, 2013 11:19 AM

Rampage
 
4 Attachment(s)
Combination of new and used products as well as an accumulation of items I purchased from users.

Using my Lian Li case that I've had for a few years - PC-Z60 Lian Li

http://www.ocaholic.ch/xoops/html/mo...iPC-Z60_01.JPG

Items so far
  • Asus Maximus V Formula
  • Intel 3770K
  • Pair of Trident X F3-2400C10D-16GTX
  • Pair of Samsung 840 Pro SSD 256GB each - Raid 0 - what the hell :biggrin:
  • 1 WD 2TB Caviar Black HD
  • Enzotech Sapphire waterblock SCW-REV A with Enzotech 1156-Z retention module
  • Box of Bitzpower barbs and compression fittings.
  • 1/2OD - like the look of the bigger tubes
  • Pair of Spectre Pro - White 120mm - there ok - like the led light for the cooling chamber area
  • Scythe SFF21E - had these for sometime, most reliable, performing /db I've used - for the rad
  • XSPC RX240 dual radiator - thick sucker
  • Lian Li PCZ60 case - clean and professional looking
  • XSPC reservoir with D5 pump
  • Antec 1000W power supply


TOOLS and BANDAGES

Makita 90 degree drill, Dewalt 18v, Milwaukee jigsaw, Arrow hand rivet gun, lots of sandpaper, spray paint, safety glasses, and supplies etc...bandages and tetanus shot:sad:

First, I drilled out the rivets to remove the hot swap sata chamber, cut it down and relocated it to the side, making sure that if I win the lottery, I can install 3 Titans ! - yeah right :haha:

Sanded down the rad, added a drain in the bottom, two coats of clear lacquer and added some lexan to separate the cooling chamber from the rest of the case. Also drilled an access whole at the bottom of the case to get to the welded drain. Cut a square whole out to run the tubing to the upper CD chamber areas where the reservoir will be installed.

Do you see my lucky $2 bill ?:punk:

Mark March 21, 2013 11:23 AM

4 Attachment(s)
More pics here

Mark March 21, 2013 11:27 AM

2 Attachment(s)
Now I did spray paint the rad originally but didn't like it and opted for a paint scrape, sand and lacquer finish instead. Added a drain in the bottom since it will be the lowest part of the case. Fully pressure tested and passed.

Mark March 21, 2013 11:35 AM

4 Attachment(s)
I relocated the swap chamber to the side, riveted all together, drilled and tapped for some added mb screws so I can put in the Lexan beerier. Also cut the back of the case ( rectangular area ) so I can easily plug in the sata and power cables to the SSD and HD. Waiting for more supplies including ( the u-channel is a must for the cut out area's in a Lian Li case ).
  1. 1x 6ft u-channel
  2. 1x 12" x 12" Di-Noc CF sheet
  3. 1x PC Window Applique "Asus ROG"
  4. 1x Molex Pin Removal Tool
  5. 1x 120mm Silver Overkill Turbine
  6. From MnpcTech.com

zoom314 April 29, 2013 07:03 AM

Nice pics there, I'll be watching this thread, as I like what I see.

Mark May 2, 2013 08:05 AM

I was going to post more pics since I've done allot more but there seems to be a lack of interest.

lowfat May 2, 2013 02:23 PM

Quote:

Originally Posted by Mark (Post 706709)
I was going to post more pics since I've done allot more but there seems to be a lack of interest.

Most people who browse worklogs generally don't post anything in the thread so I say keep on posting. :thumb:

stoanee May 2, 2013 02:46 PM

Yes, carry on!

Slik May 2, 2013 03:26 PM

We're all interested,we need more pics. It's looking good!


All times are GMT -7. The time now is 05:45 AM.