Go Back   Hardware Canucks > PC BUILDERS & TWEAKERS CORNER > Case Mods, Worklog & Gallery

    
Reply
 
LinkBack Thread Tools Display Modes
  #31 (permalink)  
Old June 24, 2012, 04:05 PM
ZZLEE's Avatar
Hall Of Fame
F@H
 
Join Date: May 2009
Location: KANATA
Posts: 2,092

My System Specs

Default

nice window mod looks cool. : )
__________________
"EVGA hunted down the last dozen or so expats living in Karachi." SKY
Reply With Quote
  #32 (permalink)  
Old June 24, 2012, 05:12 PM
Mnpctech's Avatar
Allstar
 
Join Date: Oct 2009
Location: Minnesota
Posts: 844
Default

Lovin the updates, such a cool build....
Reply With Quote
  #33 (permalink)  
Old June 24, 2012, 05:30 PM
Father Fuzzy's Avatar
MVP
 
Join Date: Jan 2012
Location: B.C.
Posts: 474

My System Specs

Default

Quote:
Originally Posted by ZZLEE View Post
nice window mod looks cool. : )
Thank you

Quote:
Originally Posted by Mnpctech View Post
Lovin the updates, such a cool build....
Thanks alot Bill your mod ruler/grills/screws/modders mesh are really paying off on this build they are Fantastic
Reply With Quote
  #34 (permalink)  
Old June 27, 2012, 12:15 AM
Father Fuzzy's Avatar
MVP
 
Join Date: Jan 2012
Location: B.C.
Posts: 474

My System Specs

Default Tubing Madness

After a couple tries at the tubing decided no quick disconnects
will be barbs with black zapstraps

Loop order is rez-pump-240rad-cpu-120rad-Gpu-rez



Drain installed with Bitspower valve plus end cap



Bitspower tee to rez



trying to clean up some of the wiring



Nice warning



Graphics hookup



Time to leaktest and sleeve a few cables

Reply With Quote
  #35 (permalink)  
Old June 27, 2012, 10:51 AM
Mnpctech's Avatar
Allstar
 
Join Date: Oct 2009
Location: Minnesota
Posts: 844
Default

Good to hear, next time you order, give me heads up, I'll toss in a sample of something.

and Keep these awesome updates rollin in
Reply With Quote
  #36 (permalink)  
Old June 27, 2012, 01:07 PM
Overclocking.ca's Avatar
Top Prospect
 
Join Date: Apr 2012
Location: Nepean, ON
Posts: 150

My System Specs

Default

Did you have to do any modification to the water block's backplate to fit on that board?
Reply With Quote
  #37 (permalink)  
Old June 27, 2012, 02:43 PM
Prolab's Avatar
MVP
F@H
 
Join Date: Jul 2010
Location: Mississauga
Posts: 485

My System Specs

Default

Where did you get those QDC for the CPU block?

Ive been looking for awhile to get those.
__________________
Gaming Rig:
-Swiffy MCP35x X2, (2) Aphacool UT60 480 rad, Heatkiller rev. 3.0, i7 3930k @ 4.6 Ghz, 16 GB G.SKILL F3, Asus Rampage IV Extreme, XFX R9 290 w/ XPSC WB, Crucial M4 128GB & 240 GB Intel 530, (5) 3 TB Toshiba Drive, Corsair AX1200, Win 7 Ult 64-bit

HTPC Rig:
-G3258 @ Stock, Asrock Z97 Pro 4, Gigabyte 270x, 500 GB WD Black, (5) 2 TB WD Green, (1) 3 TB Toshiba HD, (1) 2 TB Samsung F4, Fractal Design R3, Corsair HX620 PS, Win 7 Ult 64-bit
Reply With Quote
  #38 (permalink)  
Old June 27, 2012, 02:54 PM
dandelioneater's Avatar
Hall Of Fame
F@H
 
Join Date: Dec 2010
Location: Kelowna, BC
Posts: 1,114

My System Specs

Default

Quote:
Originally Posted by Prolab View Post
Where did you get those QDC for the CPU block?

Ive been looking for awhile to get those.
I haven't seen someone put QDC's directly onto the cpu block before. I bet that would be handy for changing components/motherboards.
__________________
Reply With Quote
  #39 (permalink)  
Old June 27, 2012, 09:09 PM
Father Fuzzy's Avatar
MVP
 
Join Date: Jan 2012
Location: B.C.
Posts: 474

My System Specs

Default

Quote:
Originally Posted by Mnpctech View Post
Good to hear, next time you order, give me heads up, I'll toss in a sample of something.

and Keep these awesome updates rollin in
I will for sure
Quote:
Originally Posted by Overclocking.ca View Post
Did you have to do any modification to the water block's backplate to fit on that board?
I was about to cut it then I used extra washers to get off that chip/block thang
and was extra carefull about that turning into xtra pressure on the chip

Quote:
Originally Posted by Prolab View Post
Where did you get those QDC for the CPU block?

Ive been looking for awhile to get those.
I got them at ncix and a few from dazmode I have a ton of them in my 44 Magnum rig
so I can swap out motherboard tray which I hope to try soon

It was just too tight in the prodigy with the qdc's and 3/4 Tubing and fittings onhand also fiqured I wouldn't be swapping it out much only itx board I have

A 200 mm rad would fit nice in this Case and keep the 5.25 drivebay
Reply With Quote
  #40 (permalink)  
Old June 28, 2012, 02:34 AM
bundymania's Avatar
Top Prospect
 
Join Date: Feb 2012
Location: Germany
Posts: 229
Default

Very nice case & worklog you have there ! The modding stuff from Bill looks awesome, maybe he wants to equip one of my next builds with some items :) ! I plan to get the black prodigy version, when its available here in germany. Some questions regarding to the rad configuaration: Is it possible to install a 240 rad in the front AND in the top, both with 25mm fans ? Or a 200mm rad in the front and another 240 in the top ?

Thanks and keep on modding :)
Reply With Quote
Reply


Thread Tools
Display Modes

Similar Threads
Thread Thread Starter Forum Replies Last Post
WIP Watercooled Bitfenix Shinobi Pabz0r545 Case Mods, Worklog & Gallery 20 July 11, 2012 12:30 AM
Bitfenix Spectre Pro Bohrman Air Cooling 19 June 5, 2012 08:49 AM
Bitfenix Survivor Core enaberif Cases 6 December 12, 2010 04:30 AM
New case manufacturer, BitFenix Mnpctech Cases 15 June 13, 2010 06:26 PM
[WTB] watercooled ati videocards. or 1 watercooled nvidia card kyle_L Buy/Sell & Trade 4 February 26, 2009 12:53 PM