Hardware Canucks

Hardware Canucks (http://www.hardwarecanucks.com/forum/)
-   Case Mods, Worklog & Gallery (http://www.hardwarecanucks.com/forum/case-mods-worklog-gallery/)
-   -   I caved... Quad GTX 580 UD with new AC waterblocks.. New 990X and new 1500W PSU (http://www.hardwarecanucks.com/forum/case-mods-worklog-gallery/45386-i-caved-quad-gtx-580-ud-new-ac-waterblocks-new-990x-new-1500w-psu.html)

Phatboy69 August 3, 2011 10:52 PM

I caved... Quad GTX 580 UD with new AC waterblocks.. New 990X and new 1500W PSU
 
I'd been mulling over for a while trying to decide if i should wait for next gen GPU's and CPU's..

Well I cracked... I have 4 new Gigabyte GTX 580 UDs in my possession and have ordered Aquacomputer blocks and SLI bridge and new 990X CPU to go with it.
Oh and some MDPC sleeving to finally finish the system.

EDIT:19-8-11 Updated list and pics
Ordered AC Kryos HF Silver CPU block and 3x AC Ramplex Ram blocks too with 24GB of (3 x 4GB) PC3-16000 2000MHz DDR3 RAM - 9-10-9-27 kits.
2 x Enermax 1500W PSU
2 x Sliding 180-Degree U Connector (CNT-MEAU) = $19.48
6 x Nozzle Body, 4-Way Brass [no nozzles] (ADT-XUTX4) = $44.94
6 x Nozzle Coupling Adapter, G 1/4 Male-Female (ADT-XMF) = $14.94
6 x Nozzle Coupling Adapter, Male-Male (ADT-XMM) = $14.94
6 x Nozzle Coupling Adapter, Female-Female (ADT-XFF) = $16.44
10 x Nozzle Socket Plug (SCR-CP003PG) = $19.90
2 x Fitting Pair, Swiveling Elbow (Low Profile) (NZL-LXG2P) = $39.98
4 x Nozzle Coupling Adapter, Male-Female, 20mm (ADT-XMF-L) = $13.96
6 x Swiveling Coupling Adapter, Male-Female (ADT-SMF) = $20.94
6 x Swiveling Coupling Adapter, Male-Male (ADT-SMM) = $20.94
4 x Nozzle Body, 5-Way Brass [no nozzles] (SPL-XUFY5B) = $33.96
2 x Fitting Pair, Swiveling Elbow (NZL-LXG1P) = $39.98
2 x Dual VID Connector, Adjustable 2-3 Slot Spacing (CNT-VDA34) = $29.98
4 x RAM-35 Sliding Connector (Type 3) (CNT-ME3) = $27.96
6 x QDC (High Flow) No-Spill Shutoff Male, Threaded G 1/4 (VL3N-MG) = $65.94
4 x QDC (High Flow) No-Spill Shutoff, Female Angle [For ID: 10mm (3/8in), OD: 13mm (1/2in)] (VL3N-F10L) = $60.96
4 x QDC (High Flow) No-Spill Shutoff, Female [For ID: 10mm (3/8in), OD: 13mm (1/2in)] (VL3N-F10S) = $51.96
6 x QDC (High Flow) No-Spill Shutoff, Male [For ID: 10mm (3/8in), OD: 13mm (1/2in)] (VL3N-M10S) = $68.94
4 x Tecnofront AirBox 360 Plexi (AIRBOX360) $99.80
1 x Sunbeamtech Power Supply Modding Tool Kit (SB-TOOLKIT) $14.99
5 x *** HOT *** Arctic Cooling MX-4 Ultra Premium Thermal Compound with High Thermal Conductivity (ACTC-MX4) $49.75
7 x Indigo Xtreme for Intel Core i7 Processors (LGA1366 socket) (INDIGO-EX-1366) $139.65
8 x 3M 8815 Thermally Conductive AdhesiveTape (3M-8815) $23.60
176-9801 1 Wire,equipment,hook up,UL1007,30.5m,24 awg,red
1 Reel of 30 Metre(s) $22.20 $22.20
176-9794 1 Wire,equipment,hook up,UL1007,30.5m,24 awg,black
1 Reel of 30 Metre(s) $22.20 $22.20
332-001 1 Wire,equipment,hook up,UL1007,30.5m,24 awg,yellow
1 Reel of 30 Metre(s) $18.10 $18.10
176-9823 1 Wire,equipment,hook up,UL1007,30.5m,24 awg,blue
1 Reel of 30 Metre(s) $22.20 $22.20
333-436 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,yellow
1 Reel of 30 Metre(s) $28.00 $28.00
331-749 1 Wire,equipment,hook up,UL1007,30.5m,18 awg,black
1 Reel of 30 Metre(s) $26.10 $26.10
331-755 1 Wire,equipment,hook up,UL1007,30.5m,18 awg,red
1 Reel of 30 Metre(s) $27.80 $27.80
331-828 1 Wire,equipment,hook up,UL1007,30.5m,18 awg,violet
1 Reel of 30 Metre(s) $26.10 $26.10
331-777 1 Wire,equipment,hook up,UL1007,30.5m,18 awg,yellow
1 Reel of 30 Metre(s) $26.10 $26.10
333-420 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,green
1 Reel of 30 Metre(s) $32.90 $32.90
333-385 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,white
1 Reel of 30 Metre(s) $32.90 $32.90
333-470 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,grey
1 Reel of 30 Metre(s) $32.90 $32.90
333-414 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,red
1 Reel of 30 Metre(s) $32.90 $32.90
333-408 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,black
1 Reel of 30 Metre(s) $32.90 $32.90
333-464 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,orange
1 Reel of 30 Metre(s) $28.00 $28.00
333-442 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,blue
1 Reel of 30 Metre(s) $35.00 $35.00
333-458 1 Wire,equipment,hook up,UL1007,30.5m,16 awg,brown
1 Reel of 30 Metre(s) $32.90 $32.90
3 MDPC Sleeve-Kit SL-K1-BK 35,29 105,87
1 MDPC Crimping-Tool CR-TOOL-X 31,63 31,63
5 SATA Crimp-Connector CR-SATA 2,09 10,45
5 SATA Power-Connector THROUGH HO-SATA-T 2,93 14,65
3 Crimp contacts FEMALE for ATX, PCIE, EPS CR-ATX-F 2,93 8,79
3 Crimp contacts MALE for ATX, PCIE, EPS CR-ATX-M 2,93 8,79
3 Crimp contacts for fans CR-FAN 2,51 7,53
3 24-Pin MOLEX BLACK - Housing HO-24P-BK 2,10 6,30
6 4-Pin MOLEX BLACK - Housing HO-4PF-BK 1,76 10,56
6 3-Pin MOLEX BLACK - Housing HO-3PF-BK 1,76 10,56
3 Cable-Management-Clip SMALL - BLACK PC-S-BK 1,89 5,67
3 Cable-Management-Clip BIG - BLACK PC-B-BK 2,48 7,44
3 Cable-Management-Clip JUMBO - BLACK PC-J-BK 2,51 7,53
SubTotal : 235,77

Of course the poor old coolermaster 1250 PSU isnt up to the task with these (it keeps doing overload shutdowns) so Ive had to order a new Enermax 1500W PSU.
As a temporary work around I've installed another 1200W supply into the MM case and it now runs 3 cards and the second UD9 MB pcie 12v connector and its mostly stable with the other supply doing accessories MB and CPU and 1 GPU. It gets through 3Dmark11 Performance settings but not Extreme and cant finish vantage without tripping overload either even with 2 1200W PSUs!
The individual rails on my 1200s are only good for 20A which explains it. They are operating right on the edge with max CPU overclock and 4 580s in benching.

Ive gone with TWO Enermax 1500's as they have 125A over 6 rails (30A each) for a total power of 1500W for GPU/CPU 12v rails as apposed to the Silverstone strider that can only do 110A (25A each) over 8 rails and max 1300W for 12v rails. The Enermax has also got some pretty tight regulation according to the couple reviews i found.

I cant believe how much power these cards draw and how much heat they generate in an SLI config. 100c on the first card without secondary active cooling, 70c on the 4th.
Ive hooked up a workable temporary solution with a 120 fan mounted above them sucking air up and another 120 blowing cooler in from the back of the cards. Dropped temps to ~70c under load for all cards at stock 795/2000.
I wasn't going to WC these so i could sell them off in a few months but they just get too hot and noisy and the performance is just amazing!

Crysis 2 DX11 ultra pack rocks with these cards.. hows minimum 100FPS with maxed out settings sound?

Ill post some pics soon...
Here's what they'll look like!
https://blufiles.storage.live.com/y1...BXTw/23515.jpg
https://blufiles.storage.live.com/y1...Es/23501_3.jpg
https://blufiles.storage.live.com/y1...xut4/21562.jpg
https://blufiles.storage.live.com/y1...pE/26023_5.jpg
https://blufiles.storage.live.com/y1...MR1500EGTs.jpg https://blufiles.storage.live.com/y1...MR1500EGTs.jpg

https://blufiles.storage.live.com/y1...o/IMG_2202.JPG

https://blu1.storage.live.com/items/...-SU2S2_l-2.jpg

https://blufiles.storage.live.com/y1...o/IMG_2217.JPG

https://blufiles.storage.live.com/y1...4c454ed1-0.jpg

https://blufiles.storage.live.com/y1...c6589ad4-0.jpg

https://blu1.storage.live.com/items/...1024/photo.JPG

Did an inventory of the Koolance bits today... Tadah!

https://blufiles.storage.live.com/y1...G_2224edit.jpg



The ramplex manifolds I made I may use, and other manifold bit n pieces... or I may just use the extendable 180o at the back right and do a more simple serial setup for the ram blocks.
https://blufiles.storage.live.com/y1...G_2227edit.jpg


Quick disconnects, Ill probably be moving most of these away from the MB and GPU's to the Rads and Res now instead, to keep the Mboard looking cleaner. See if I like it or not.
https://blufiles.storage.live.com/y1...(1024x770).jpg


Various Adapters, swivel joiners, extendable joiners, and plugs...
https://blu1.storage.live.com/items/...G_2230edit.jpg

GT7R August 3, 2011 11:27 PM

Now that's everything a pc freak could possibly want :)
Enjoy the hell of it!

Andy August 4, 2011 12:30 AM

Geebus ... some serious gear there ... need build pics!

Phatboy69 August 4, 2011 01:05 AM

Quote:

Originally Posted by Andy (Post 538202)
Geebus ... some serious gear there ... need build pics!

You can see my build for the Borg cube a few threads below which will give you an idea of whats already in the system. The real difference will be when I get the waterblocks/SLI bridge and sleeving done.

_dangtx_ August 4, 2011 01:33 AM

im thinking you could trip the braker or perhaps do the wall socket in if the wires are old and puny and such

still, have a fold bro! kickin' system you gots there.

Phatboy69 August 4, 2011 04:04 AM

Quote:

Originally Posted by _dangtx_ (Post 538209)
im thinking you could trip the braker or perhaps do the wall socket in if the wires are old and puny and such

still, have a fold bro! kickin' system you gots there.

Thanks mate.. down under here in Australia we have 240V 10Amp & 15Amp circuits so it will only draw 7Amps at 90% efficiency at max power draw.(~1700W) We can do 2400W from the wall on standard circuits & 3600W on 15Amp circuits.

RBA August 4, 2011 05:04 AM

I can imagine your wallet caved as well ... Amazing system you have there... Enjoy!

Eldonko August 4, 2011 08:05 AM

Awesome, enjoy!

_dangtx_ August 4, 2011 09:45 AM

time to update your location and have loads of fun!!!

trayton August 4, 2011 10:41 AM

Wow nice system, you must not be married or have children and I presume your the president of a small to mid size country to afford all that.

Have fun though should be awesome machine!


All times are GMT -7. The time now is 01:10 AM.